Metal 3D Printing
Metal 3D printing builds a part directly from metal powder or metal-filled filament, one layer at a time, straight from a digital file. There’s no mold to cut and no block of stock material to machine down. That’s why it’s become a real option for aerospace brackets, medical implants, tooling inserts, and production parts that need to be strong, precise, and available faster than a casting or machining lead time would normally allow.
At Agile Manufacturing, we run two different metal 3D printing technologies: Direct Metal Laser Sintering (DMLS) and Markforged’s Metal X system. They solve similar problems in different ways, and figuring out which one fits your part is usually the first real decision in a metal 3D printing project.
How Metal 3D Printing Works
There are two main routes to a metal part on our floor, and they don’t work the same way.
DMLS uses a high-powered laser to fuse fine metal powder, layer by layer, inside a sealed, inert gas chamber. The laser traces the shape of each cross section directly from the CAD file, melting the powder just enough to fuse it to the layer below. Once the build is done, the part is stress-relieved, cut off its build plate, and finished, which may include heat treatment, machining critical surfaces, or media blasting, depending on the application. DMLS parts come out dense and mechanically sound, close to what you’d get from a wrought or cast metal part.
Metal X, Markforged’s system, works more like FDM but with a metal-filled filament instead of plastic. The printer lays down a “green” part made of metal powder bound in a plastic matrix. That green part then undergoes a debinding step to remove most of the binder, followed by a sintering cycle in a furnace that burns off the remaining binder and fuses the metal particles, shrinking the part to its final dimensions. It’s a slower path to a finished part than DMLS in terms of total cycle time, but the printer itself is far less expensive to run, which changes the economics for certain jobs.
Neither one is strictly better. DMLS tends to win on tight tolerances, complex internal geometry, and applications where you need the part validated against aerospace or medical grade standards. Metal X tends to win on cost per part for simpler geometries and on turnaround for teams that want a metal prototype without the lead time or expense of DMLS.
Metal 3D Printing Materials
Material choice comes down to what the part needs to survive, not just what looks good on a spec sheet.
- Stainless steel is the most common starting point for both DMLS and Metal X parts. It machines and finishes well, resists corrosion, and covers most general-purpose and food- or medical-adjacent applications.
- Tool steel gets used where a part needs to hold an edge or resist wear, conformal cooling inserts for injection molds being a common example.
- Aluminum, typically AlSi10Mg, is the go-to when weight matters as much as strength, which is most of the time in aerospace and automotive brackets.
You can find full material properties, including the AlSi10Mg data sheet, on our DMLS materials page. If your part doesn’t actually need metal, and the goal is more about visual accuracy or a low volume run of a plastic-like component, cast urethane is often the more cost-effective route, and it’s worth ruling out before committing to a metal build.
Metal 3D Printing vs. CNC Machining and Casting
The honest answer is that metal 3D printing doesn’t replace CNC machining or casting; it sits alongside them, and the right choice depends on the part and the volume.
CNC machining still wins for tight tolerance features, large flat surfaces, and parts made from bar or plate stock where geometry is simple. Casting still wins once you’re producing thousands of an identical part and the tooling cost is justified by the run length. Metal 3D printing earns its place in the gap between those two: complex geometry that would be difficult or impossible to machine, internal channels or lattice structures that no mold could produce, and production runs too small to justify a casting tool.
A useful way to think about it: if you already know you need thousands of an unchanging part, metal 3D printing probably isn’t your answer. If you need a handful of complex, high-value parts, or you’re still validating the design and don’t want to commit to tooling yet, it usually is.
Applications We See Most Often
- Aerospace: brackets, ducting, and lightweight structural components where reducing mass has a direct performance payoff.
- Automotive and motorsport: prototype and low-volume production parts, especially where a design is still being iterated.
- Medical and dental: patient-specific instruments and implant components, usually paired with a validated material and a documented process.
- Tooling: conformal cooling channels in injection mold inserts, jigs, and fixtures that need to survive daily use on a shop floor.
- End-use production parts: low to mid volume runs where the part’s complexity or the cost of tooling makes metal 3D printing the more practical route.
Designing a Part for Metal 3D Printing
A few things to plan for before you send us a file:
- Support structures. Both DMLS and Metal X need supports on overhangs and certain internal features, and those supports have to be removed after the build. Design with that removal step in mind, especially for enclosed cavities.
- Wall thickness. Very thin walls can warp or fail to fuse cleanly. We’ll flag this during design review if we see it.
- Post-processing. Decide early whether the part needs machined critical surfaces, heat treatment, or a specific surface finish, since that affects both cost and lead time.
- Orientation. How a part sits on the build plate affects surface finish, support requirements, and mechanical properties in different directions. This is usually worth a conversation before the file goes to print.
Why Manufacturers Work With Agile Manufacturing for Metal 3D Printing
We run both DMLS and Metal X in-house, which means we can recommend the technology that actually fits your part instead of steering every job toward whichever machine we happen to own. Our team reviews designs for manufacturability before printing, not after, and we handle the post-processing, machining, and finishing in-house so a metal part doesn’t have to travel to three different vendors before it’s usable.
We’re ISO 9001:2015 registered, and we ship across Canada and the United States. If you’re weighing metal 3D printing against machining or casting for an upcoming project, our team can help you figure out which route actually makes sense before you commit to tooling or a production method.
Frequently Asked Questions
Metal 3D printing builds a part directly from metal powder or metal-filled filament, layer by layer, based on a digital file. It skips the mold or block of stock material that traditional casting and machining require, which makes it well suited to complex geometry and low- to mid volume production.
DMLS uses a laser to fuse metal powder directly inside an inert gas chamber, producing dense, mechanically sound parts suited to tight tolerances and validated applications. Metal X prints a metal-filled filament into a green part, which is then debound and sintered in a furnace. DMLS generally costs more per part but holds tighter tolerances, while Metal X is more economical for simpler geometries and faster prototyping.
The most common options are stainless steel, tool steel, and aluminum, typically AlSi10Mg. Material choice depends on what the part needs to withstand, whether that’s corrosion resistance, wear resistance, or a low weight-to-strength ratio.
DMLS parts are dense and can match or come close to wrought or cast material properties, particularly once heat treated. Metal X parts, after sintering, are also fully dense metal, though mechanical properties vary by material and should be checked against your application’s requirements.
It tends to make sense for complex geometry that’s difficult to machine, internal features a mold can’t produce, and production volumes too small to justify tooling costs. For very simple geometries at high volume, casting or machining is usually still the more economical choice.
Yes. Agile Manufacturing runs both DMLS and Markforged Metal X systems in-house, with material properties available on our DMLS materials page and equipment details on our metal 3D printers page. We serve clients across Canada and the United States, and you can keep up with broader industry developments on our additive manufacturing news page.







